Carbide Drill Recommended Cutting Conditions

Model Number
TAC-RESDBA / TAC-RESDRA / TAC-RFESDB / TAC-RFESDRA / TAC-HESDB / TAC-HESDR

■ Cutting Speeds, Rotational Speeds and Feed Amounts
When abnormal vibration or sounds occur during cutting, adjust the cutting conditions.

For TAC-WMESDRA, refer to the above conditions for TAC-RESDRA and use similarly.
For TAC-CR-RFESDBA / TAC-CR-RFESDRA / TAC-CR-RFSDB / TAC-CR-RFSDR / TAC-ESDBA / TAC-ESDRA, refer to the above conditions for TAC-RFESDRA and use similarly.
For TAC-RSDB / TAC-RSDR / TSC-DL-ESDB / TSC-DL-ESDR / TAC-DL-SESDR, refer to the above conditions for TAC-RESDRA and use similarly.
For TAC-HRESDB / TAC-HRESDR, increase the rotational speed by 10 to 20% from the above conditions for TAC-RESDRA, and use similar feed amount conditions.

Model Number
TAC-ESDB / TAC-ESDR / TAC-MS-ESDR

■ Cutting Speeds, Rotational Speeds and Feed Amounts
When abnormal vibration or sounds occur during cutting, adjust the cutting conditions.

For TAC-WMESDRA, use under conditions increased by 20 to 30% from the above conditions for TAC-ESDR.

Model Number
TAC-SDB / TAC-SDS / C-SDB / C-SDS / TAC-SDXL

■ Cutting Speeds, Rotational Speeds and Feed Amounts
When abnormal vibration or sounds occur during cutting, adjust the cutting conditions.

For TAC-HSDXL, use under conditions increased by 20 to 30% from the above conditions for TAC-SDXL.
The above cutting conditions for TAC-SDXL / TAC-HSDXL have been set based on 10 x D. In the case of depths other than these, adjust these conditions by referring to the table below.

Model Number
TAC-BNESDBA / TAC-ESD3FRA / TAC-ESD3FB

For TAC-HBNESDR, use under conditions increased by 20 to 40% from the above conditions for TAC-BNESDBA.

Model Number
TAC-SC-SDR / TAC-SF-SDR / C-SC-TSDR

Model Number
TAC-ESD2LB

Model Number
TSC-CR-XESDR / TSC-XESDR / TSC-XESDM / TSC-XSDR / TSC-XSDM

Model Number
TSC-XESD2LB

Model Number
DLC-ALESDR / DLC-DL-ALESDR

Model Number
DLC-SC-SDR / DLC-SF-SDR

Model Number
TAC-FCESD3R

Model Number
SEC-PLSDB

Model Number
BUNDR / BUNDRS

Model Number
TAC-NCSPD / TAC-LS-NCSPD / TAC-MS-HNCSPD

For TAC-LS-NCSPD, use with feed amount lowered by about 20 to 30%.
When performing V groove machining on the TAC-MS-HNCSPD, use with feed speed lowered by about 30 to 50%.
For SEC-NCSPD, use with the rotational speed and feed amount lowered by about 20 to 30%.

Model Number
TAC-CTDA / TAC-CTDAL / TAC-CTDACW

For TAC-CTDAL, use with feed amount lowered by about 20 to 30%.

Model Number
TAC-CS3M / TAC-LS-CS3M

For TAC-LS-CS3M, use with feed amount lowered by about 20 to 30%.